Your target should be 60 percent quality at bats, with at least 40 percent coming from hard hit balls. Sure, these numbers are hard to achieve, but most players will be at 50 percent and 30 percent, respectively. Remember, quality at bats leads to lots of hits.
David Kennedy. A quality at bat (QAB) on GameChanger Classic is any one of the following: At bat with 3 pitches after 2 strikes. At bat with 6+ pitches. Extra base hit.
Contact% is, as it sounds, the overall percentage of contact you’re making per swing. MLB average is around 80%, with Joe Panik leading the league at 89.9% and (you guessed it) Joey Gallo posting the worst mark at a horrifying 59.1%.
How Important are Quality at-Bats? Quality at-bats are a critical aspect of any MLB team. Sometimes having a QAB might not show up in the box score or highlight reel, but it can be a game-changer in the outcome.
A Quality At-Bats is any plate appearance that results in a: Hard it ball. Walk.
Definition. Slugging percentage represents the total number of bases a player records per at-bat. Unlike on-base percentage, slugging percentage deals only with hits and does not include walks and hit-by-pitches in its equation. Slugging percentage differs from batting average in that all hits are not valued equally.
Definition. An official at-bat comes when a batter reaches base via a fielder’s choice, hit or an error (not including catcher’s interference) or when a batter is put out on a non-sacrifice. (Whereas a plate appearance refers to each completed turn batting, regardless of the result.)
Contact rate (CT%) is the percentage of at-bats in which a hitter makes contact; that is does not strike out. The calculation is (AB - K)/AB. In the Major Leagues, the average CT% is ~75%. Hitters with 90+% contact rates are typically elite in batting average.
75-80 mphElite Level Exit Velo Averages By Age
|PLAYER AGE RANGE||AVE EXIT VELOCITY|
|Ages (11-13)||56-65 mph|
|Ages (14-15)||75-80 mph|
|JV (15-16)||80 mph aluminum / 75 mph wood|
|Varsity (15-18)||90 mph aluminum/85 mph wood|
An OPS+ of 100 is defined to be the league average. An OPS+ of 150 or more is excellent and 125 very good, while an OPS+ of 75 or below is poor.
Definition. Statcast defines a ‘hard-hit ball’ as one hit with an exit velocity of 95 mph or higher, and a player’s “hard-hit rate” is simply showing the percentage of batted balls that were hit at 95 mph or more.
The league average BABIP is typically around . 300. Pitchers who have allowed a high percentage of hits on balls in play will typically regress to the mean, and vice versa.
Times on base include hits, walks and hit-by-pitches, but do not include errors, times reached on a fielder’s choice or a dropped third strike.
The requirements are different than the traditional definition; the game is a shutout victory where the starting pitcher pitches the entire game while allowing no hits, and no runs are scored (a no-hitter by the traditional definition runs may score by walk, hit by pitch, defensive interference, errors, stolen bases, …
A simple way to compute a player’s batting average is to divide the player’s total hits (not the number of bases) by his/her total at bats. A walk does not count as an at bat or hit, and does not affect a player’s batting average.
The “Olympic Rings” or platinum sombrero applies to a player striking out five times in a game. A horn refers to a player striking out six times in a game; the term was coined by pitcher Mike Flanagan after teammate Sam Horn of the Baltimore Orioles accomplished the feat in an extra-inning game in 1991.
360 is considered to be above average. If a player’s OBP hits . 370 or higher, it puts them among the top players in the league for this statistic.
The best possible score a player can have for an on-base percentage is 1.000 – this indicates a player gets on base 100% of the time he comes to the plate for a plate appearance (PA). No one does this – a good OBP is somewhere over .
The last spot in your lineup should be reserved for the worst batter on your team. By definition, they will receive the fewest at-bats out of any spot in the lineup, thus mitigating their ineffectiveness quite a bit.
Your best hitters should bat in the number three and number four spots in the order. Put the speedier (and/or higher on-base) of the two in the number three slot. Follow that up with your next best on-base guys in the number one and two spots.
1 is that batting second allows for more runners on base. It’s kind of a best-of-both-worlds solution relative to the leadoff and cleanup spots, adding more plate appearances but also leaving some RBI chances.
Is it possible to have a slugging average of more than 1? No, because in order to have a slugging average that is higher than one, you would have to hit home runs every time you were up to bat.
To calculate slugging percentage, use the formula: SP = total bases ÷ at bats, where total bases is the number of bases the player ran from hits, and at bats is the number of times they were up to bat.
Check out the velocity chart in this article that uses physics data from one of the world’s baseball physics experts, Dr. Alan Nathan. His calculator of fly ball distance is a great estimator, and it shows that somewhere between 77-82 is needed to throw approximately 300 feet.